Sysnet Board คู่มือ การใช้งานอุปกรณ์ Network

การ Config อุปกรณ์ เครือข่าย Network Device => อุปกรณ์ VOIP, IP-PBX, ระบบโทรศัพท์-ตู้สาขา ผ่าน IP => หัวข้อที่ตั้งโดย: wildarms เมื่อ วันที่ 9 กุมภาพันธ์ 2011, 11:22:39

ชื่อ: ผม config ตัว linksys pap2t ยังไงครับ
โดย: wildarms เมื่อ วันที่ 9 กุมภาพันธ์ 2011, 11:22:39
ผมหาดูแล้วไม่เจอการ config  ที่ใข้กับบริการ ของ totnetcall ของ tot เลยครับ
ชื่อ: Re: ผม config ตัว linksys pap2t ยังไงครับ
โดย: yod เมื่อ วันที่ 9 กุมภาพันธ์ 2011, 17:09:59


สวัสดีครับ

รุ่น PAP2T ผมยังไม่ได้ทำลง webboard ครับ

แต่ลองดูใน board นี้ครับ

http://webboard.totnetcall.com/smf/index.php?topic=47.0 (http://webboard.totnetcall.com/smf/index.php?topic=47.0)
ชื่อ: Re: ผม config ตัว linksys pap2t ยังไงครับ
โดย: wildarms เมื่อ วันที่ 9 กุมภาพันธ์ 2011, 20:04:35
ชอบคุณครับ ผม config เสร็วแล้ว ครับ และมี ปัญญหา ใหม่เกิดละครับ

มีปัญญาหา ตรง ที่ โทรออกได้ แต่ โทรเข้า ไม่ได้ครับ ผม ลอง กดโทรเข้าแล้วมันบอกว่าวิธีกดผิดอ่ะครับ โทรจากมือถือ ของ dtac กับ ais และ เบอร์บ้าน ก็บอกเหมือนกันหมดเลย แต่ เบอร์ cdam ของ cat  โทรติด ได้

ผมเซ็ตตาม Set From  TOT Netcall

Line 1 or 2

Line Enable                 =  yes
Sip  Port                       =  5061
Proxy                             =  203.113.125.82
Register              =   yes
Make call without reg  =  no
Ans call without reg     =  no
Register Expires          =   3600
Display Name               =  068109xxxxx

Display                           =  0681xxxxxxx
Pass word                      =  xxxxxxx
User ID                            = 068109xxxxx
Use Auth id                    =   no

Audio Configuration  

Preferred Codec:  G711a                       Silence Supp Enable:  No
Use Pref Codec Only  no                      FAX CED Detect Enable:  Yes
DTMF Tx Method:  Auto                        


SYSTEM
Enable Web server     :  yes
CHCP      :  no
Static IP      :  192.168.1.134
Gateway      :  255.255.255.0
NetMask      :  192.168.1.1
DNS  Query Mode   :  Parallel
Debug level   :  0

SIP

RTP Port Min        :  16384
RTP Port Max        :  16384
NSE Dynamic Payload  :  100
AVT Dynamic Payload  ;  101
G726r16 Dynamic        :  98
G726r40 Dynamic Payload: :  96
G726r24 Dynamic Payload:  97
G729b Dynamic Payload  :   99
Basic View (switch to advanced)


SIP Parameters    
Max Forward:     70
Max Auth:       2
Max redirection             5
SIP Server Name:   $VERSION
SIP User Agent Name:$VERSION
DTMF Relay MIME   application/dtmf-relay
Hook Flash MIME Type:  application/hook-flash
Remove Last Reg:  NO
Use Compact Header:  NO
Escape Display Name:  NO
RFC 2543 Call Hold:  Yes


Supplementary Service Settings

CW Setting: Yes      Block CID Setting:      no
Block ANC Setting: No   DND Setting:     no
CID Setting: yes      CWCID Setting:     yes
Dist Ring Setting: yes      Secure Call Setting:     no
Message Waiting: no      DND Activated:     no

NAT Support Parameters  

Handle VIA received:  yes   Handle VIA rport:     yes
Insert VIA received:   yes   Insert VIA rport:     yes
Substitute VIA Addr:  no   Send Resp To Src Port: no
STUN Enable:  no      STUN Test Enable:    no
        NAT Keep Alive Intvl: 15



แล้วไป Port Forwarding  ที่ เร้าเตอร์
Service  068109xxxx  Port 5061    Server IP 203.113.125.82

นี้หมดเลย
ชื่อ: Re: ผม config ตัว linksys pap2t ยังไงครับ
โดย: ekkasitseo1 เมื่อ วันที่ 14 กุมภาพันธ์ 2011, 20:58:32
ขอบคุณครับ